Electricity: revision questions and answers
Test yourself first. Say or write your answer, then tap the question to check it and see why. Free, no sign-up.
Test yourself
Define electric current.
Answer: The rate of flow of electrical charge
Why: Current tells you how much charge passes a point each second, which is why it is a rate and not an amount.
State the equation linking potential difference, current, and resistance.
Answer: V = I × R
Why: Potential difference is the push, resistance is the opposition, so the current you get is whatever those two settle on: more push gives more current, more resistance gives less.
Name the component whose resistance decreases as temperature increases.
Answer: Thermistor
Why: Heating a thermistor frees up more charge to move through it, so the hotter it gets the easier current flows.
State the colour of the live wire in a three-core mains cable.
Answer: Brown
Why: In UK and European three-core cable the live is brown, the neutral blue, and the earth green and yellow. Older UK cable used red for live, so never judge an old installation by colour alone.
Calculate the charge that flows when a current of 4 A flows for 25 s.
Answer: Q = I × t = 4 × 25 = 100 C
Why: Write Q = I x t, substitute 4 x 25, multiply to get 100 C.
Describe the resistance of a diode when connected in each direction.
Answer: Very low resistance in one direction (forward); very high resistance in the other (reverse)
Why: A diode is a one-way valve for current: charge passes easily the forward way and is almost completely blocked the other way.
State whether adding resistors in parallel increases or decreases the circuit's total resistance.
Answer: Decreases
Why: Each new branch is another route for charge to take, and more paths mean the current flows more easily overall.
(Higher) State the transformer equation.
Answer: Vp × Ip = Vs × Is
Why: A transformer cannot create energy, so if it raises the voltage the current must drop by the same factor to keep power in equal to power out.
What you need to know
Everything this topic covers, as a checklist. Can you explain each one without your notes?
- Draw and interpret circuit diagrams using standard circuit symbols.
- Explain that a closed circuit needs a source of potential difference for charge to flow, define electric current as the rate of flow of electrical charge, and use
Q = I × t(charge flow in coulombs; current in amperes; time in seconds): knowing current has the same value at any point in a single closed loop. - Explain that a component's current depends on its resistance and the potential difference across it (greater resistance means smaller current for a given potential difference), and use
V = I × R(potential difference in volts; current in amperes; resistance in ohms): questions may use either "potential difference" or "voltage," and both are creditable. - Explain that some resistors (ohmic conductors, at constant temperature) have constant resistance, where current is directly proportional to potential difference, while others' resistance changes with current: a filament lamp's resistance increases as its filament heats up; a diode conducts in one direction only, with very high resistance in reverse; a thermistor's resistance decreases as temperature increases (used in circuits such as thermostats); an LDR's resistance decreases as light intensity increases (used in circuits such as automatic lighting), explain how to design a circuit to measure a component's resistance (via current and potential difference), draw the correct circuit diagram, and use I, V graphs to judge whether a component is linear or non-linear and relate that curve shape to its function.
- Describe the difference between series and parallel circuits, and explain qualitatively why adding resistors in series increases total resistance while adding them in parallel decreases it. For components in series: the current is the same through each component, the supply's total potential difference is shared between them, and total resistance is the sum of the individual resistances (
R_total = R₁ + R₂). For components in parallel: the potential difference across each is the same, total current is the sum of the currents through each branch, and total resistance is less than the smallest individual resistance (calculating the actual total parallel resistance value is not required). Construct and check series/parallel circuits from diagrams, explain the design of dc series circuits for measurement/testing, calculate current/potential difference/resistance in dc series circuits, and solve series-circuit problems using equivalent resistance. - Explain that mains electricity is an ac supply (UK domestic supply: 50 Hz, about 230 V), and explain the difference between direct and alternating potential difference.
- Describe three-core mains cable's colour-coded wires (live, brown; neutral, blue; earth, green/yellow stripes), explain that the live wire carries the alternating supply potential difference (~230 V relative to earth's 0 V), the neutral wire completes the circuit (at or near 0 V), and the earth wire is a safety wire only carrying current if a fault occurs, explain why a live wire can be dangerous even with the mains switch open, and the dangers of any connection between live and earth.
- Explain how a circuit device's power relates to the potential difference across it and current through it, and to energy change over time, using
P = V × IandP = I² × R(power in watts; potential difference in volts; current in amperes; resistance in ohms). - Describe how everyday appliances transfer energy, from batteries or the ac mains to a motor's kinetic energy or a heating device's thermal energy, explain that the energy an appliance transfers depends on how long it runs and its power, and that work is done when charge flows in a circuit; use
E = P × tandE = Q × V(energy transferred in joules; power in watts; time in seconds; charge flow in coulombs; potential difference in volts); explain how a device's power relates to potential difference/current and to energy transferred over time, and describe the relationship, with examples, between an appliance's power rating and how its stored energy changes in use. - Describe the National Grid as the network of cables and transformers connecting power stations to consumers, explain that step-up transformers raise potential difference for efficient transmission while step-down transformers lower it for safe domestic use, and explain why the National Grid is an efficient way to transfer energy overall: detailed knowledge of a transformer's internal structure is not required.
Higher tier only
- Select and use the transformer equation (supplied on the equation sheet): potential difference across the primary coil × current in the primary coil = potential difference across the secondary coil × current in the secondary coil.
Play it as a game
Common mistakes
- Confusing current and potential difference, particularly treating them as the same measurable "amount of electricity," rather than distinguishing current (charge flow rate) from potential difference (energy transferred per unit charge, driving that flow).
- Assuming current is "used up" as it passes around a series circuit, rather than understanding current is the same at every point in a single loop, while potential difference (not current) is what's shared between series components.
- Applying the series resistance-adds rule to a parallel circuit or vice versa: these two behave in genuinely opposite ways for both current and resistance, and mixing them up is one of the most common electricity errors.
- Believing the neutral wire is always completely safe because it sits near 0 V, rather than understanding only the earth wire is a dedicated safety conductor, and that live-to-neutral or live-to-earth contact can both still be dangerous.
- Mixing up step-up and step-down transformers' roles in the National Grid, or forgetting the purpose of stepping up voltage for transmission is to reduce transmission energy losses, not simply "to travel further."
Key words
Current, potential difference, resistance, ohmic conductor, thermistor, LDR, diode, series circuit, parallel circuit, alternating current, direct current, live wire, neutral wire, earth wire, power, National Grid, transformer (HT).
Mix it up: questions from other topics
Mixing topics helps you remember more. These come from topics that link to this one.
State the equation used to calculate power.
Answer: P = E ÷ t
Why: Power is about speed of energy transfer, so you share the energy out over the time it took: the same energy moved in less time means more power.
From EnergyGive one example of a non-renewable energy resource.
Answer: Any one of: coal, oil, gas, nuclear fuel
Why: These fuels took millions of years to form underground, so once we burn them they are gone within a human lifetime and cannot be replaced.
From EnergyDefine potable water.
Answer: Water that is safe to drink
Why: Potable does not mean pure: it means harmful microbes and salts are low enough that drinking it will not make you ill.
From Using ResourcesCalculate the kinetic energy of a 2 kg object moving at 3 m/s.
Answer: Eₖ = ½ × 2 × 3² = 9 J
Why: Write Ek = 1/2 m v squared, substitute 1/2 x 2 x 3 squared, then 3 squared is 9 so the answer is 9 J.
From EnergyDefine specific heat capacity.
Answer: The energy needed to raise the temperature of one kilogram of a substance by one degree Celsius
Why: Different substances need different amounts of energy to warm up, so this gives a fair comparison using the same mass and the same temperature rise.
From Energy(Higher) Name the two biological methods of extracting metal from low-grade ores.
Answer: Phytomining and bioleaching
Why: Both use living things to do the hard work: plants or bacteria concentrate the metal from ore too poor to be worth normal mining.
From Using Resources(Higher) Give one way to increase the efficiency of an intended energy transfer.
Answer: e.g. lubricating moving parts, to reduce energy wasted as heat by friction (accept other valid methods with reasons)
Why: Efficiency rises when less energy is wasted, and oil between moving parts cuts the friction that was quietly turning useful energy into heat.
From EnergyTeachers
The full lesson for this topic (slides, worksheet, quizzes and more) is on the Electricity topic page.